MS Slow after update to 4.50.14 on suse
MailScanner at ecs.soton.ac.uk
Fri Feb 3 10:04:42 GMT 2006
-----BEGIN PGP SIGNED MESSAGE-----
On 3 Feb 2006, at 09:49, Glenn Steen wrote:
> On 03/02/06, Julian Field <MailScanner at ecs.soton.ac.uk> wrote:
>> -----BEGIN PGP SIGNED MESSAGE-----
>> On 2 Feb 2006, at 22:05, Glenn Steen wrote:
>>> On 02/02/06, Scott Silva <ssilva at sgvwater.com> wrote:
>>>> Glenn Steen spake the following on 2/2/2006 1:05 PM:
>>>>> On 02/02/06, Scott Silva <ssilva at sgvwater.com> wrote:
>>>>>> One problem I see is either an old or no file
>>>>>> /etc/MailScanner/reports/en/languages.conf. See if this is
>>>>>> either a 0 length
>>>>>> file, or if you have a /etc/MailScanner/reports/en/
>>>>>> languages.conf.rpmnew file.
>>>>> Ah yes. I actually (he said blushing) walked into that myself this
>>>>> time around... Silly cut'n'paste all the three lines... Oh
>>>>> well, if
>>>>> that is it, it¨s just a matter of moving languages.old back into
>>>>> Jules, perhaps you should stress the need to look for an rpmnew
>>>>> first, before blithely doing the upgrade(s)?... In the nice usage
>>>>> would be a good place...
>>>>> -- Glenn
>>>>> email: glenn < dot > steen < at > gmail < dot > com
>>>>> work: glenn < dot > steen < at > ap1 < dot > se
>>>> I thought Julian had fixed the upgrade_languages_conf to not do
>>>> this a few
>>>> months ago. Maybe my rememberer is busted...
>>>> I usually check, now, after being bitten by this one.
>>> If so, he managed to un-fix it to this version:-). If you cu'n'oaste
>>> the suggested lines to do the upgrade the first one creates the
>>> zero.length file, and the subsequent move move it into place...
>>> Empirical study (meaning: I goofed up:) show that it certainly will
>>> behave as I describe;)
>> Check you upgrade_MailScanner_conf or upgrade_languages_conf (one is
>> a link to the other) for this code
>> Usage() unless $oldfname && $newfname &&
>> -f $oldfname && -f $newfname &&
>> -s $oldfname && -s $newfname;
>> That really should do the job.
> Not really... The instructions are the in the Usage itself:
> If you are using the RPM distributions then try this:
> cd /etc/MailScanner/reports/en
> upgrade_languages_conf languages.conf languages.conf.rpmnew >
> mv -f languages.conf languages.old
> mv -f languages.new languages.conf
> Now, the upgrade thing behaves exactly right, BUT you still create a
> zero-lenght file because the Usage is printed to STDERR, and _nothing_
> to STDOUT. Sure, it's pretty obvious whatwith the Usage carooming by
> on the screen, but still... If you try to make all this "unattended"
> or is a bit preoccupied with other things (that'd be me:-) it just
> _might_ slip by (not that I did let that happen, mind you:-).
> Note that this is singularly for when you do a cut'n'paste _from the
> Usage itself_. So having a few words about _not doing it if there's no
> rpmnew file_ might be a good idea. Specifically since this tend to
> crop up from time to time:-).
So if the Usage is printed, I need to cat the incoming file to stdout
as well. Will that fix it? I'm not sure I 100% understand you if that
is not right.
Buy the MailScanner book at www.MailScanner.info/store
PGP footprint: EE81 D763 3DB0 0BFD E1DC 7222 11F6 5947 1415 B654
-----BEGIN PGP SIGNATURE-----
Version: PGP Desktop 9.0.4 (Build 4042)
-----END PGP SIGNATURE-----
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
More information about the MailScanner