Problem with the Installer

[Eli Wapniarski]

Never mind... I had a problem with the perl development environment. Once I reinstalled perl-devel everythnig seems to be building correctly.

Thank You for any attention that you might have put into this.

Eli


On Friday 01 May 2009 20:27:51 Eli Wapniarski wrote:
> Hi
> 
> I just tried to install version MailScanner-4.76.24-1.rpm.tar.gz on Fedora 10 x86_64 and I'm getting
> 
> I think your system will build architecture-dependent modules for x86_64
> 
> Deleting all the old versions of your Perl modules,
> I will re-install them in a minute.                
> 
> Removing perl-ExtUtils-MakeMaker
> Removing perl-TimeDate          
> Removing perl-Pod-Escapes       
> Removing perl-Pod-Simple        
> Removing perl-Test-Harness      
> Removing perl-Test-Simple       
> Removing perl-IO-stringy        
> Removing perl-HTML-Tagset       
> Removing perl-HTML-Parser       
> Removing perl-Compress-Zlib     
> Removing perl-DBI               
> Removing perl-Digest-SHA1       
> Removing perl-Digest-HMAC       
> Removing perl-Net-DNS           
> Perl modules have been removed...
> 
> Rebuilding all the Perl RPMs for your version of Perl
> 
> Oh good, module File-Spec version 0.82 is already installed.
> 
> Attempting to build and install perl-ExtUtils-MakeMaker-6.50-1
> Installing perl-ExtUtils-MakeMaker-6.50-1.src.rpm             
> Executing(%prep): /bin/sh -e /var/tmp/rpm-tmp.yH6vlt          
> + umask 022                                                   
> + cd /root/rpmbuild/BUILD                                     
> + LANG=C                                                      
> + export LANG                                                 
> + unset DISPLAY                                               
> + cd /root/rpmbuild/BUILD                                     
> + rm -rf ExtUtils-MakeMaker-6.50                              
> + /bin/gzip -dc /root/rpmbuild/SOURCES/ExtUtils-MakeMaker-6.50.tar.gz
> + /bin/tar -xf -                                                     
> + STATUS=0                                                           
> + '[' 0 -ne 0 ']'                                                    
> + cd ExtUtils-MakeMaker-6.50                                         
> + /bin/chmod -Rf a+rX,u+w,g-w,o-w .                                  
> + exit 0                                                             
> Executing(%build): /bin/sh -e /var/tmp/rpm-tmp.6jpseI                
> + umask 022                                                          
> + cd /root/rpmbuild/BUILD                                            
> + cd ExtUtils-MakeMaker-6.50                                         
> + LANG=C                                                             
> + export LANG                                                        
> + unset DISPLAY                                                      
> + CFLAGS='-O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic'
> + perl Makefile.PL INSTALLDIRS=vendor                                                                                             
> Warning: prerequisite Pod::Man 0 not found.                                                                                       
> Checking if your kit is complete...                                                                                               
> Looks good                                                                                                                        
> Using included version of ExtUtils::Command (1.16) as it is newer than the installed version (1.13).                              
> Writing Makefile for ExtUtils::MakeMaker                                                                                          
> + make                                                                                                                            
> Can't locate ExtUtils/Install.pm in @INC (@INC contains: blib/arch blib/lib /usr/local/lib64/perl5/site_perl/5.10.0/x86_64-linux-thread-multi /usr/local/lib64/perl5/site_perl/5.10.0 /usr/local/lib64/perl5/site_perl /usr/local/lib/perl5/site_perl/5.10.0 /usr/local/lib/perl5/site_perl /usr/lib64/perl5/vendor_perl/5.10.0/x86_64-linux-thread-multi /usr/lib64/perl5/vendor_perl/5.10.0 /usr/lib64/perl5/vendor_perl /usr/lib/perl5/vendor_perl/5.10.0 /usr/lib/perl5/vendor_perl /usr/lib/perl5/site_perl/5.10.0 /usr/lib/perl5/site_perl /usr/local/lib64/perl5/site_perl/5.10.0/x86_64-linux-thread-multi /usr/local/lib/perl5/site_perl/5.10.0 /usr/lib64/perl5/vendor_perl/5.10.0/x86_64-linux-thread-multi /usr/lib/perl5/vendor_perl/5.10.0 /usr/lib/perl5/vendor_perl /usr/lib64/perl5/5.10.0/x86_64-linux-thread-multi /usr/lib/perl5/5.10.0 /usr/lib/perl5/site_perl/5.10.0 /usr/lib/perl5/site_perl .).                                                      
> BEGIN failed--compilation aborted.                                                                                                                           
> make: *** [pm_to_blib] Error 2                                                                                                                               
> error: Bad exit status from /var/tmp/rpm-tmp.6jpseI (%build)                                                                                                 
> 
> 
> RPM build errors:
>     Bad exit status from /var/tmp/rpm-tmp.6jpseI (%build)
> 

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.mailscanner.info/pipermail/mailscanner/attachments/20090502/b3306196/attachment.html