Too messages in Hold folder when spamassassin is activated in MailScanner

[UxBoD]

if both debugs take so long please post your outout.  if your users are strangling your bandwidth through HTTP then that needs to be looked at aswell through policy.

Regards,

--[ UxBoD ]--
// PGP Key: "curl -s https://www.splatnix.net/uxbod.asc | gpg --import"
// Fingerprint: C759 8F52 1D17 B3C5 5854  36BD 1FB1 B02F 5DB5 687B
// Keyserver: www.keyserver.net Key-ID: 0x5DB5687B
// Phone: +44 845 869 2749 SIP Phone: uxbod at sip.splatnix.net

----- Original Message -----
From: "Israel Garcia" <igalvarez at gmail.com>
To: "MailScanner discussion" <mailscanner at lists.mailscanner.info>
Sent: Tuesday, November 27, 2007 9:37:08 PM (GMT) Europe/London
Subject: Re: Too messages in Hold folder when spamassassin is activated in MailScanner


On Nov 27, 2007 4:13 PM, Glenn Steen < glenn.steen at gmail.com > wrote: 




On 27/11/2007, Israel Garcia < igalvarez at gmail.com > wrote: 
> On Nov 27, 2007 1:11 PM, UxBoD < uxbod at splatnix.net > wrote: 
> 
> > Well ASN is hashed out in your v320 pre file but is still active in the 
> v310 file. 
> What does it means? 
That you should comment it out in the v310.pre file too;-) 
Then restart MS (with SA) and see if that cures it. 


DONE!!.. I restarted now.. let see now :-) .. two questions, which is the difference in init.pre, v310.pre, v310.pre and v320.pre files? What is ASN? thanks a lot glenn..:-) 



> > We process over 100k messages a day on a 256k line so no real worries 
> there. You say a high percentage of your traffic is SMTP, how are you 
> identifying that ? 
> 
> I can see the traffic in my WAN network using a cisco router/netflow 
> collector. 
> 
> > Are you performing any sort of packet shaping or QoS then ? 
> No 
> > It does sound to me like DNS timeouts when performing lookups, as others 
> have also said. 
> Well, I use a only caching dns ( caching-nameserver-7.3-3) 
> > If you set the list of RBLs to check to blank in MailScanner.conf does 
> the problem disappear ? 
> Do you mean thie line: 
> Spam List = #ORDB-RBL SBL+XBL spamcop.net NJABL SORBS # 
Ok, that's empty then. 


> When the problem disappear is when I set: 
> Use Spamassassin = no 
> and restart mailscanner... 

If you run "MailScanner --debug --debug-sa", or just a normal 
"spamassassin -D -t </path/to/some/test/message", do you see any ... 
very noticeable ... "pauses"? And if so, where? 

Well, I ran MailScanner --debug --debug-sa and I see no errors.. BUT it takes so long.. I mean several minutes (20 or 30 minutes) :-( 

regards 
israel 



> thanks in advance 
> Israel 



> 

Cheers 
-- 
-- Glenn 
email: glenn < dot > steen < at > gmail < dot > com 
work: glenn < dot > steen < at > ap1 < dot > se 
-- 
MailScanner mailing list 
mailscanner at lists.mailscanner.info 
http://lists.mailscanner.info/mailman/listinfo/mailscanner 

Before posting, read http://wiki.mailscanner.info/posting 

Support MailScanner development - buy the book off the website! 



-- 
Regards; 
Israel Garcia 
-- 
This message has been scanned for viruses and 
dangerous content by MailScanner , and is 
believed to be clean. 
-- 
MailScanner mailing list
mailscanner at lists.mailscanner.info
http://lists.mailscanner.info/mailman/listinfo/mailscanner

Before posting, read http://wiki.mailscanner.info/posting

Support MailScanner development - buy the book off the website! 

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.